 | |
     1/16th scale HD 3D Printed 1/16th scale M4 Sherman Family brush guard set. Set includes the brush guards for the headlights, siren, and tail lights. The set is fully detailed with the weld bead details, and headlight cover plugs. The set also contains enough parts for 2 tanks...$68.00 each set 
 
 1/16th scale HL M1A2 Lexan polycarbonate copula periscope insert set. The set contains a section of clear Lexan Polycarbonate plastic and a section of stencils. The stencils are designed to fit on the periscope section of the HL M1A2 Abrams copula. The set is designed for the builder to cut out and hand fit the periscopes to the model, the stencils give you a good idea on where to cut / sand so the periscopes are the perfect size. The Polycarbonate is Lexan so it is very easy to work with and does not shatter like Acrylic. The Set gives you enough stencil periscopes for 2 tanks...$15.00 each set 
 1/16th scale M1 Abrams 3D printed Tow shackles set. Set includes two patterns of shackles: the hook pattern and the U hook pattern. The set also contains the pins to secure each to the tank. The set includes more than enough to fully equip 1 Heng Long Abrams tank model...$57.00 each set 
1/16th scale HD 3D printed M1A2 Abrams replacement loader's hatch periscope set. Set contains 2 HD 3D printed Periscope housings (enough for 2 tanks), and a section of clear lexan plastic to be used as a lens insert. Set is intended to replace the molded in unit found on the stock HL M1A2 model...$35.00 each set 
 1/16th scale HD 3D printed M1A2 Abrams turret detail upgrade set. Set includes the following parts, underside drainage guard, Storage bin handles, rear blow out panels vent fastener straps, rear blowout panels securing fastener straps, rear blow out panels lifting rings, and the front turret hex bolts. The lifting rings have two options with the orientation of the hook. The set also supplies you with enough parts for 2 M1A2 models, plus several extras...$85.00 each set 
 
 
 1/16th scale HD 3D printed MP-65 antenna base 10 pack set. Set includes 5 MP-65 antenna bases... $50.00 each set 
 1/16th scale HD 3D printed MP-65 antenna base 5 pack set. Set includes 5 MP-65 antenna bases... $35.00 each set
 1/16th scale HD 3D printed King Tiger side hull side skirt mounts set. Set includes the main side skirt mounts and the rear side skirt mounts. The mounts have their weld bead details present. The set contains enough mounts to equip 3 King tiger tanks...$65.00 each set 
 1/16th scale HD 3D printed M1 Abrams shrouded Coax detail set. Set is designed to replace the stock coax detail on the Heng Long M1A2 Abrams MBT model. The set has the correct shape of reinforcement ribs, welds and the unit is printed hollow. The set contains 5 units which is enough to upgrade 5 M1A2 Abrams tank models...$38.00 each set 
 1/16th scale HD 3d Printed Heng Long M1A2 Abrams CITV lens insert detailing set. Set includes an interior insert sleeve that slips into the hollow Heng Long M1A2 Abrams kit supplied CITV lens housing giving you the interior and face lens detailing. The set also includes a section of Lexan clear polycarbonate for the clear lens detailing. The set contains 2 inserts and enough lexan for 2 lenses. This set can upgrade 2 M1A2 Abrams tanks...$40.00 each set 
1/16th scale HD 3D print M1A2 style Front Driver hatch detail upgrade set. Set includes lots of detail accessories to upgrade the surface detailing on the Heng Long M1A2 Abrams model. The set includes the hatch rim, the rear hatch locking system, two options for the hatch pivot cover knob, the front hull power receptacle, and the clear printed bow hatch periscope insert. All of these units are fully detailed with all the correct welds, fasteners, and other features. There are also enough parts to upgrade 2 M1 Abrams tanks, plus several parts are duplicated for use of spares...$90.00 each set 
 
 
 
 1/16th scale HD 3D print M1A1 style Front Driver hatch detail upgrade set. Set includes lots of detail accessories to upgrade the surface detailing on the Heng Long M1A2 Abrams model. The set includes the hatch rim, the rear hatch locking system, two options for the hatch pivot cover knob, the front hull power receptacle, and the clear printed bow hatch periscope insert. All of these units are fully detailed with all the correct welds, fasteners, and other features. There are also enough parts to upgrade 2 M1 Abrams tanks, plus several parts are duplicated for use of spares...$90.00 each set
 
1/16th scale HD 3D printed M1 Abrams family front hull power receptacle set. Set includes 3 units, enough to equip 3 M1 family of tanks. The sets are designed for use on the Heng Long M1A2 Abrams model, but may also be able to work on other 1/16th scale M1 tanks that are on the market. The units are fully detailed with all weld, fastener and geometry detailing...$32.00 each set
1/16th scale HD 3D printed M1 Abrams turret front CIP panels 2 pack set. Set includes 4 CIP panels that are designed to replace the molded in units found on the stock Heng Long M1A2 Abrams tank model. These replacement sets are better detailed with the Velcro corner straps present. The set contains 4 units which is enough to equip 2 M1A2 Abrams tank models...$55.00 each set. 
 1/16th scale HD 3D printed M1 Abrams turret front CIP panels set. Set includes 2 CIP panels that are designed to replace the molded in units found on the stock Heng Long M1A2 Abrams tank model. These replacement sets are better detailed with the Velcro corner straps present. The set contains 2 units which is enough to equip one M1A2 Abrams tank model...$35.00 each set. 
1/16th scale cast rubber M1 Abrams front mudflap tips set. Set includes 2 cast rubber front mudflap tips, enough for 1 M1 Abrams model. The det is designed to replace the stock molded in units that are present on the HL M1A2 Abrams model. The set is made out of cast black rubber off of masters that were HD 3D Printed...$20.00 each set 
 1/16th scale HD 3D printed M1A2 Abrams 120mm gun collimator device set. The unit is designed to replace the molded in collimator molded into the barrel tip of the HL M1A2 Abrams 120mm barrel. The unit is highly detailed with fastener, support, riveted data plate, and optic details. The Unit is at the correct off center angle and will give the correct detailing to the HL barrel tip. The set contains 4 collimators, enough to equip 4 tanks...$35.00 each set 
 
 1/16th scale HD 3D printed M1A2 Abrams Gunner's optic box closed armored shutters face detail set. Set contains the closed shutter details that enhance the Heng Long 1/16th scale gunner's optic box shutters. The set contains the correct shutter shape hinge and spring details. The units are designed to drop directly onto the stock HL unit with no drilling or modding, just place directly over. The set contains two units, enough to equip 2 Abrams tanks...$32.00 each set. 
1/16th scale HD 3D printed M1 Abrams Tow cable mount set. Set is designed for use on the Heng Long M1A2 Abrams mode. The Set recycles the kit supplied town cables and gives the added detailing of the clamps, and end sections to enhance the HL model. The set supplies you with enough parts to equip 2 HL M1A2 Abrams models...$35.00 each set. 
 
 1/16th scale HD 3D Printed M1 Abrams / Post WWII US AFV Smoke grenade cartridge set. This set is designed to supply the smoke grenade canisters that would be loaded on the turret smoke grenade launchers on Post WWII US tanks. This set is designed for the HL M1A2 Abrams Smoke Grenade launchers and is a drop in installation. The set contains 2 styles of grenades, the M82, and the M90. The set contains enough grenades for two models, and s few extras for spares. With the set you can also mix the styles of grenades on the model adding more detailing. $40.00 each set 
 
 1/16th scale 3D Printed M1 Abrams family front lower rear hull detail plate detail set. Set is designed to cover / go over the front lower plate found on the HL M1 Abrams model. This set covers up the model's fastener locations that are present on this portion of the model. Also included on the printing are the 2 front tow hook mounts. These are drilled out and have the weld bead details present. 4 magnets (not pictured) are also included with the set... $45.00 each set 
 
 1/16th scale Clear HD 3D printed resin HL M1A2 Abrams bow driver's hatch periscope detail insert set. This component is a drop in insert that adds the missing periscope lens detailing to the driver's hatch on the HL M1A2 The set contains 2 inserts. Enough to upgrade 2 tanks... $45.00 each
1/16th scale HD 3D Printed M60 tank family side storage bin latches set. Set gives you enough parts to upgrade 3 M60 family of tanks. The handles are fully detailed with the padlock / over extension stops, and the weld beads are present. They are also in a right and left hand format as per the real vehicle...$40.00 each set 
 1/16th scale HD 3D Printed AS-3900 antenna base set. Set includes 5 AS-3900 antenna bases. The units are fully detailed with the fasteners and rubber antenna cover, and spring details present. the set also includes metal antenna wires...$40.00 each set 
 1/16th scale HD 3D Printed AB-558 antenna base set. set includes 5 AB-558 antenna bases. The units are fully detailed with the fasteners and rubber antenna stem details present. These sets are not designed for use with an antenna wire...$35.00 each set 
 1/16th scale HD 3D printed Modern era NATO AFV Antenna base set. Set includes 5 AB-558 antenna bases and 5 AS-3900 antenna bases. Both units are fully detailes with fastener details, and the AS-3900 units have the spring details, and rubber end cap details present. metal antennas are also included for the AS-900 units... $50.00 each set
 1/16th scale HD 3D Printed early production sherman tank turret 50.cal barrel clamp storage set. Set replicates the early pattern of turret top mounted M2HB 50.cal barrel storage system. The set includes the rabbit ears front end barrel clamp on riser, and the rear hinged clamp system. The rear unit is functional with the latch and the cover plate. Both units have the weld bead and rivet details present. The set contains enough parts and spares for 2 tanks... $42.00 each set 
  1/16th scale HD 3D printed M4 sherman tank family bow travel lock set. Set contains the main gun travel lock, and the retention latch details. The travel lock is fully detailed with front and rear detailing present, cast number details, and lock mechanism details. The unit is functional in that the unit can hinge outward. The retention latch is also fully detailed with the lock, mount and base details. Both the travel lock mounting feet and the latch base have their weld bead details integrally printed for added accuracy and detailing. $33.00 each set 
 
 1/16th scale HD 3D printed M1 Abrams upper hull detail set. Set includes the side skirt fastener mounting strips, fire extinguisher box, storage bin handles, and the bilge pump tube. The strips have all the fastener details present, and these parts are in duplicate to be used for spares or for use on another model. The Fire extinguisher box is a direct replacement for the kit's molded in unit. The new unit features the correct depth, weld bead and handle details. The unit is a single print so no other assembly is required. The bin handles have the correct shape for the M1 and also include the pre welded pad lock stop details. The set also gives you 2 extra for use as a spare or to outfit another model. The bilge pump tube features all the weld bead details, rubber top portion, and the hose clamp detailing...$65.00 each 
  
 
 
1/16th scale HD 3D printed M1A2 Abrams rear tail light brush guard 5 pack set. Set contains 5 guards, enough to equip 5 Abrams tanks. The guard slips over the right hand tail light cluster. The set is designed to work on the HL or the ECA M1 Abrams Tail light upgrade set (listed Below and NOT INCLUDED)...$50.00 each set 
 
1/16h scale 3D Printed Heng Long USMC M1A2 Abrams snorkel tubes set. Set includes the rear deflector and the top deck air breather tubes. The rear deflector grill is designed to fit onto the Stock deflector grill frame mount. This set also includes the three snorkel tubes. All 3 tubes are designed to be removable so tank can be displayed with the tubes in the deployed or removed state...$105.00 each set 
 
  1/16th scale 3D Printed Heng Long USMC M1A2 Abrams snorkel set. Set includes the rear deflector and the top deck air breather tubes. The rear deflector grill is designed to fit onto the Stock deflector grill frame mount. This set DOES NOT INCLUDE THE SNORKEL TUBES ...$65.00 each set
1/16th scale 3D Printed Heng Long M1 Abrams replacement engine grill detail enhancement set, style 4. This set is designed to replace the molded in rear grill work area on the stock HL M1A2 Abrams kit giving the model better detail accuracy and more realism. The set contains a single detail inset that contains the exhaust louvers for the two rear engine hatches. The louvers have all rear grillwork mounting strap and weld bead details in place and have the correct number of louvers for each of the hinge panels. The hinge lock details are also present as is the bottom deflector section. The set is also designed to be used with the stock smoke system and there are provisions for hooking the exhaust smoke tubes up to the center deflector section so smoke emits from the correct area. The set also includes two HD 3d Printed outer protective grill panel sections to obtain the optimal level of detailing for this section of the model. This version of the insert replicates the style that is commonly found on USMC tanks with the rear snorkel / exhaust deflector mount present. In addition to the above this set also comes with the Snorkel mounting equipment. The deflector mount is integrally printed onto the grillwork frame. The mount has the correct shape and has all the fastener holes present. This set includes the rear mounted deflector duct, the two intakes for the air intake which are attached to the top left hand side grillwork. This set also includes the snorkel tubes. This would include the main exhaust stack, and the two air intake tubes. The tubes are removable and the model can be displayed with or without the tubes. This set will require hand fitting to install and is only for very experienced modelers with the proper tools and skill sets to properly mount in place... $160.00 each set 
 
 1/16th scale 3D Printed Heng Long M1 Abrams replacement engine grill detail enhancement set, style 3. This set is designed to replace the molded in rear grill work area on the stock HL M1A2 Abrams kit giving the model better detail accuracy and more realism. The set contains a single detail inset that contains the exhaust louvers for the two rear engine hatches. The louvers have all rear grillwork mounting strap and weld bead details in place and have the correct number of louvers for each of the hinge panels. The hinge lock details are also present as is the bottom deflector section. The set is also designed to be used with the stock smoke system and there are provisions for hooking the exhaust smoke tubes up to the center deflector section so smoke emits from the correct area. The set also includes two HD 3d Printed outer protective grill panel sections to obtain the optimal level of detailing for this section of the model. This version of the insert replicates the style that is commonly found on USMC tanks with the rear snorkel / exhaust deflector mount present. In addition to the above this set also comes with the Snorkel mounting equipment. The deflector mount is integrally printed onto the grillwork frame. The mount has the correct shape and has all the fastener holes present. This set also includes the rear mounted deflector duct, and the two intakes for the air intake which are attached to the top left hand side grillwork. The snorkel tubes themselves are NOT INCLUDED WITH THIS SET. This set will require hand fitting to install and is only for very experienced modelers with the proper tools and skill sets to properly mount in place... $110.00 each set
1/16th scale 3D Printed Heng Long M1 Abrams replacement engine grill detail enhancement set, style 2. This set is designed to replace the molded in rear grill work area on the stock HL M1A2 Abrams kit giving the model better detail accuracy and more realism. The set contains a single detail inset that contains the exhaust louvers for the two rear engine hatches. The louvers have all rear grillwork mounting strap and weld bead details in place and have the correct number of louvers for each of the hinge panels. The hinge lock details are also present as is the bottom deflector section. The set is also designed to be used with the stock smoke system and there are provisions for hooking the exhaust smoke tubes up to the center deflector section so smoke emits from the correct area. The set also includes HD 3d Printed outer protective grill panel sections to obtain the optimal level of detailing for this section of the model. This version of the insert replicates the style that is commonly found on USMC tanks with the rear snorkel / exhaust deflector mount present. The deflector mount is integrally printed onto the grillwork frame. The mount has the correct shape and has all the fastener holes present. This set will require hand fitting to install and is only for very experienced modelers with the proper tools and skill sets to properly mount in place... $90.00 each set 
1/16th scale 3D Printed Heng Long M1 Abrams replacement engine grill detail enhancement set, style 1. This set is designed to replace the molded in rear grill work area on the stock HL M1A2 Abrams kit giving the model better detail accuracy and more realism. The set contains a single detail inset that contains the exhaust louvers for the two rear engine hatches. The louvers have all rear grillwork mounting strap and weld bead details in place and have the correct number of louvers for each of the hinge panels. The hinge lock details are also present as is the bottom deflector section. The set is also designed to be used with the stock smoke system and there are provisions for hooking the exhaust smoke tubes up to the center deflector section so smoke emits from the correct area. The set also includes HD 3d Printed outer protective grill panel sections to obtain the optimal level of detailing for this section of the model. This set will require hand fitting to install and is only for very experienced modelers with the proper tools and skill sets to properly mount in place... $90.00 each set 
 
 
 
 
 3D Printed M1 Abrams side hull detailing set. Set includes components for the bump stops, and side skirt mounts. *note set is for detail purposes only and parts must be placed where they don't make contact with the suspension travel. Also set is designed for tanks which will see light RC use. ...$77.00 each set 
 
 
 
 1/16th scale 3D Printed M1 Abrams family lower rear hull detail plate detail set. Set is designed to cover / go over the rear lower plate found on the HL M1 Abrams model. This set covers up the model's fastener locations that are present on this portion of the model. Also included are 2 HD 3D printed lower access caps, which have the correct detailing which is present on the real vehicle and 4 magnets (not pictured)... $45.00 each set 
 1/16th scale hollow 3D Printed M1 Abrams Family replacement tail light detail set style 1. Set includes two 3D printed M1 Abrams pattern tail light mounts, taillight body, and Cylindrical brush guards. The set also includes a set of translucent HD 3D printed tail light detail faces, and the right hand power cable conduit. The parts are a drop in installation and are intended to replace the stock molded in units on the Heng Long M1 Abrams tank model. The bases are a left and right hand setup and are fully detailed with the interior light mount bracket detailing and the power cable detailing. The cylindrical brush guards have the correct cutout on the corners which are far more detailed compared to the stock molded in setup found on the model. The units are a single printing and are installed as one solid unit once the molded in unit is deleted. The sets have all weld bead details present and are printed hollow to allow the stock LED to be slid in place. The lens detail faces are in HD for optimum detailing which include the fastener, flange and various lens details. The parts are printed in translucent HD to allow the LED light to emerge from the lens portion for the added detail function of the stock LED light to emerge from the unit for added realism. The set also contains two extra lens faces to be used as spares and also a length of scale wire for the conduit wiring detail... $45.00 each set 
 
 1/16th scale HD 3D printed M1A2 Abrams army pattern rear corner communication box cluster and engine hatch detail set, style 2. Set includes the Army pattern rear communication box, rear engine hatch hooks, and the rear engine hatch mounting plates. Set also includes extra hooks for use as spares... $35.00 each set 
 
 1/16th scale HD 3D printed M1A2 Abrams army pattern rear corner communication box cluster and engine hatch detail set, style 1. Set includes the Army pattern rear communication box, rear engine hatch hooks, and the rear engine hatch mounting plates. Set also includes extra hooks for use as spares... $35.00 each set 
 
 1/16th scale HD 3D Printed mid production M4A3 Sherman tank / M36 Jackson TD Main gun Travel lock set. Set is fully detailed and semi functional. The functions include the working working retract hinges. Set also includes the travel lock retention clip, and weld details. The unit is fully detailed with both front and rear details...$29.00 each set 
1/16th scale HD 3D printed Tiger I Turret Coax MG34t Barrel detail insert 5 pack. Insert is designed to replace the turret mounted airsoft firing LED that are mounted in the Coax position on the Heng long and Taigen Tiger I turret. Insert is designed to be added in place of the LED. Insert is also printed hollow to allow the LED to be mounted to the insert for Airsoft firing light, or Turret MG flash upgrading. The MG34T barrel detailing is all present. Which includes booster detailing, ratchet cutouts, stamped spring steel ratchet retention, vent holes, wrench sections, and other shroud details. The set contains 5 inserts...$33.00 each set 
 1/16th scale HD 3D printed Tiger I rear exhaust puffer cap set. Set contains 4 puffer caps in the open position and 4 in the closed position...$25.00 each set 
 1/16th scale HD 3D printed USMC M1A2 Abrams rear communication box / engine hatch upgrade set. Set includes the USMC pattern rear communication box, rear engine hatch hooks, and the rear engine hatch mounting plates. Set also includes extra hooks for use as spares... $35.00 each set 
 1/16th scale HD 3D printed IDF plastic jerry cans set. This set comes with 8 IDF pattern jerry cans. Cans are fully detailed with the cap, embossed pattern, and marking details. Jerry can holders NOT included ...$25.00 each set 
 1/16th scale HD 3D printed IDF tank turret MG cradle set. Set includes 2 M1919 / FN Mag Cradles. The cradles include all weld bead details, IDF pattern ammo can holders. The cradles are in two versions, one is the commander version and the other is the loader version. Metal mounting pins are also included Also included is the mantlet M2HB mount. This includes all the mount and weld bead details, along with the ammo can holder. M1919A4 and M2HB guns are NOT included. This set is designed to work with the HD 3D printed M1919A4 and M2HB models that are listed on shapeways.com via the following links M1919A4 M2HB $66.00 each set 
 
 
 
 
 1/16th scale Tiran 5 Turret detail set. This set includes the following parts, Rear turret storage rack, This is 3D Printed and features all inner tube structure details, welds, mounting fasteners and other details. Large turret side storage bin. Bin parts are all 3D printed, the body features the weld details. The lid is HD printed and features the hinge, hatch stops, top handle, and latch hooks. The set also comes with HD 3D printed latches. Small side turret storage bin. This part is a single HD 3D Printed part, complete with all hinge, latch, welds, mounting strap, fasteners, and armor mounting standoffs. Side turret mounted 60mm mortar. This part is a hollow HD 3D printed with all details present. This would include the carry handle w/ side gage, also present is the ball socket and the turret mount. Another supplied part is a 3D printed commander copula mortar guard with welds X2 rear antenna bases. Each of these units are HD 3D printed, and have their turret mounts present w/ power cable mount and cord details. Also present is the AS-3900 antenna base which includes all fastener spring, and rubber cover details. A length of floral wire is also included for the antenna wire Elevated US AFV Vane sight, this is the same HD 3D printed part found on WWII pattern US AFVs Turret roof twin spare 50.cal barrel storage racks. These include two pre welded brackets and several tie down handles. Also included are several spares. Commander's cupola MG pintle mount. This part is HD 3D printed and has the mounting pintle for the commander's MG Loader MG pintle mount. These parts are also HD 3D printed, and include the bracket / weld, and locking detent details. Another included component is the MG rotating telescoping extender MG pintle. This part also has all latch and other details present. *Jerry cans, Jerry can mounts, fire extinguisher, M1919 MG, and MG cradles are not included* $188.00 each set 
 
 
 
 
 1/16th scale Tiran 5 Hull Detail set 3. This includes the following parts, Front Tiran 5 pattern mudflaps, these are 3D printed and have both outer surface and interior details. these details include the fasteners, welds, inner rigidity bars, functional hinges, front retention spring hookups, HD 3D printed retension spring mounts, HD 3D printed fender open locks, Metal wire and pivot pins Also included are front and rear cast rubber mud flap tips. Both sets are made with HD 3D printed masters. The front units include the mounting bar, w/ hex head fastener details, and rigidity rib details. The rear mud flaps feature the mounting bar and hex head fastener details. The rear mudflap is designed to replace the stock molded in plastic mud flap that is found on the stock Hooben T55 model. IDF pattern front headlight brush guard. This is a 3D printed component with the weld details and the small comm box details predent. Also included is the headlight / blackout lens armored cover plate. The plate is fully removable and can be positioned on or off the model and no glues are needed to lock in place $75.00 each set 
 
 
 
 1/16th scale 3D Printed Tiran 5 Hull detail set 2. This set includes the following parts, Large rear fender storage box. This unit is HD 3D printed, and has all the mounting bracket, fastener details, hinge, and latch details present. This component is also fully functional with working hinges and two small wire pins are included Right hand side fender storage bin. This part is HD 3D printed and has all mounting bracket / fastener details, along with the lid, hinge and latch details present rear telephone communication box. This cluster of parts are HD 3D printed which contains the box, the mounting bracket, power cord mount details, weld bead / stand off lug details, hinge detailing, latch detailing, power cable, power cable armored cover w/ weld and stand off details smaller comm plug box Right hand small bracketed comm box. This HD 3D printed part has the weld, stand off lug details along with the small details found on the comm box itself IDF pattern mounted fire extinguisher. This is also HD 3D printed and contains the fire extinguisher body, and bracket. The bracket is fully detailed with bottom base, riveting, and stamp pattern details. The set also comes with 3 which are enough for 1 Tiran 5 tank $115.00 each set 
 
 
 
 
 3D printed 1/16th scale Tiran 5 hull detail set 1. This set includes the following parts, The main rear hull storage rack, this component is a single printing that contains the pre-weleded hull brackets, internal and external fasteners, and the handle detailing. Also included for the rack's details is a HD 3D printed small box that attaches to the side. The box has the hinge, lid, mounting bracket / fastener, and latch details Gun Cleaning stave holders, these are printed in HD material and have all their bracket and fastener detailing printed on Crowbar and crowbar mount. These are all printed in HD material and have their correct shape, bracket / wed detailing present. HD printed tie downs are also included which are for the stave mounts and the crowbar mounts. There are enough for the parts needed and there are also many spares that are included IDF Vehicle ID Plate. There areaer two of these HD units that are for the front and rear plate of the vehicle $70.00 each set 
 
 
 3D Printed Taigen RC motherboard cooling fan guard. This guard is designed to drop into place on the motherboard cooling fans found on the Taigen models. This is designed to prevent loose wires or cables from getting caught in the fan when in opperation, while not blocking airflow into the fan / motherboard. The unit is a drop in install part that requires no tools or mods to be made to the fan or the guard... $8.50 each 
 1/16th scale HD 3D printed HL M1 Abrams replacement hub cap set style 1. This set is designed to better replicate the clear plastic hub caps found on the real M1 Abrams tank series and is designed to be a direct drop in replacement of the stock Opaque plastic or opaque die cast metal hub caps found on the HL M1A2 model and metal aftermarket wheel sets. Set contains 20 translucent HD 3D printed hub caps. This is enough for 1 complete M1 Abrams and several spares... $52.00 Each set 
 1/16th scale HD 3D printed HL M1 Abrams replacement hub cap set style 2. This set is designed to better replicate the clear plastic hub caps found on the real M1 Abrams tank series and is designed to be a direct drop in replacement of the stock Opaque plastic or opaque die cast metal hub caps found on the HL M1A2 model and metal aftermarket wheel sets. Set contains 20 translucent HD 3D printed hub caps. This is enough for 1 complete M1 Abrams and several spares... $52.00 Each set 
1/16th scale HD 3D printed HL M1 Abrams replacement hub cap set style 3. This set is designed to better replicate the clear plastic hub caps found on the real M1 Abrams tank series and is designed to be a direct drop in replacement of the stock Opaque plastic or opaque die cast metal hub caps found on the HL M1A2 model and metal aftermarket wheel sets. Set contains 20 translucent HD 3D printed hub caps. This is enough for 1 complete M1 Abrams and several spares... $52.00 Each set 
1/16th scale HD 3D Printed M10 TD turret ammo racks set. Set includes enough parts for the 2 turret ammo racks for both the left and right hand side. Also included are the tie down strap hard points... $30.00 each set 
 1/16th scale HD 3D Printed VVSS Sherman tank rear spare track racks set. Set includes enough parts to assemble to rear track racks. All hinge details are present and can be made to function. Spare track links NOT included....$25.00 each set 
  1/16th scale 76mm Sherman turret detail set Set includes HD 3D Printed rear bustle 50.cal storage rack, receiver rack, retracted or open 50.cal travel lock, and non elevated vane sight...$25.00 each set 
 1/16th scale HD 3D Printed War Period Sherman tank 76mm barrel thread protector / counter weight. Part is designed to slip over the 76mm barrel found on the Tiagen 76mm Sherman tank model... $25.00 each 
 1/16th scale HD 3D printed Sherman family MG detail / LED insert set. Set is designed to replace the stock Taigen / HL incorrect MG details with a M1919 barrel inserts and to also secure the flash and indicator LEDs. Set includes the M1919 barrel for the Bow, Coax MGs. Set also includes the 76mm turret optic detail. The fully printed M1919A4 barrel details include the correct lengths, they are printed drilled out and have the ability to mount on the Stock LEDs... $25.00 each 
 
1/16th scale HD 3D printed M4A3 Sherman tank rear engine hatch set... $25.00 each. 
  1/16th scale, 5 pack HD 3D printed / metal tow cable set style 2. Set includes enough HD 3D printed tow cable eyes and a length of steel cable to assemble 5 cables... 32.00 each set 
 1/16th scale HD 3D printed / metal tow cable set style 2. Set includes 2 HD 3D printed tow cable eyes and a length of steel cable... 25.00 each set
 1/16th scale, 5 pack HD 3D printed / metal tow cable set style 1. Set includes enough HD 3D printed tow cable eyes and a length of steel cable to assemble 5 cables... 32.00 each set 
 1/16th scale HD 3D printed / metal tow cable set style 1. Set includes 2 HD 3D printed tow cable eyes and a length of steel cable... 25.00 each set
 1/16th scale 3D printed M4A3 Sherman rear deflector grill. The Grill is a replacement for the solid molded grills found on the taigen and HL sherman models plus the Grill will also work on the Mato sherman. The grill has all of the correct fin details and pitch. The setup also includes the retracted pivoting lever, and the securing pin. The Grill also works with the ECA cast resin M4A3 rear Hull extension upgrade set (sold separately)... $26.50 each 
 
 1/16th scale HD 3D Printed M4 sherman family front transmission cover fastener / blister set. Set gives you the fastener blister detail that is absent on all 1/16th scale Sherman tank models, and the rest of the hex head bolts found on the transmission cover sides and lower portion... $25.00 each set 
 1/16th scale 3D printed M4 sherman late pattern sprocket tooth ring set. Set includes 4 rings, your choice of materials. Standard material... $46.00 each set HD Material... $52.00 each set 
 HD 3D printed, 
 Standard Material, 
 1/16th scale HD 3D printed German Tiger I command tank conversion set. Set includes three antenna bases, umbrella frame antenna top, antenna storage tube, generator fuel cap, and hinged antenna deployment support mounts. Wire is also included with the set. All 3D printed parts are made with HD 3d printed material... $125.00 each set 
 
 
 
 1/16th scale HD 3D Printed US AFV complete bow headlights static set. Set includes 2 highly detailed bow headlights. Set is not desinged to be used with LEDs or bulbs. However the they can be used with Fiber Optics...$25.50 each set 
 1/16th scale HD 3D Printed turret detail set, set includes 1 50.cal travel lock, 1 vane sight, 1 barrel storage clip set, 1 M2 Receiver clamp. Enough for 1 75mm Sherman, or Pershing. Choose your choice between deployed or retracted travel locks. Also your choice on elevated or non elevated vane sights...$25.50 
1/16th scale HD 3D Printed 76mm T23 turret / M26 Pershing Vane sight set. Set Includes 5 non elevated vane sights... enough for 5 76mm shermans or 5 M26 Pershings...$25.50 
1/16th scale HD 3D Printed M4 Sherman tank elevated vane sight set. Set includes 5 vane sights, enough for 5 sherman tanks...$25.50 each set 
1/16th scale HD 3D Printed US tank 50.cal bustle storage rack set. Set includes enough M2HB barrel and receiver clamps to equip 5 US tanks. The receiver clamp is fully functional. This set will work on the High Bustle M4A3 Sherman, M4A3 (105) Sherman, and M26 Pershing... $33.50 each set 
 
1/16th scale 3D Printed Sherman tank lower hull escape hatch / recharge jack access point set. Set is designed to give a quick access point to a recharge jack on the lower hull of a Taigen Sherman tank model. Set is designed to work with magnets (*that are included*) to mount the hatch to the lower hull of the model, and at the same time give you the detailing of the lower hull escape hatch that is absent on the stock Taigen / Torro Sherman tank model. $21.00 Each set 
 
 1/16th scale HD 3D Printed Tiger I main gun travel lock...$21.00 each 
 
1/16th scale HD 3D Printed Tiger I removed tire hub set. Set is designed to mimic the look of the tiger I with the front tire removed from both sides. This set is designed for use on the Tamiya 1/16th scale tiger I model. One set includes two hubs, enough for 1 Tiger I tank... $21.00 each set 
1/16th scale HD 3D printed Tiger I rear hingework hooks set. Set contains 3 hooks, and all are made to be funcitonal...$20.00 each set 
1/16th scale HD 3D printed Tiger I engine hatch legs set. Set contains 2 legs in the retracted state (enough for 1 tiger I)...$20.00 each set 
   1/16th scale HD 3D printed Tiger I hingework access plate detailing set... set includes the access plate, and the lift hooks...$25.00 each set
 1/16th scale HD 3D printed US AFV retracting 50.cal travel lock retracted pack set. Set includes 5 retracting travel locks depicted in the retracted state...$20.00 each set 
 
 1/16th scale HD 3D printed US AFV retracting 50.cal travel lock open pack set. Set includes 5 retracting travel locks depicted in the deployed state...$20.00 each set 
 1/16th scale HD 3D Printed US AFV early pattern elevated 50.cal travel lock pack set. Set includes 5 early pattern travel locks...$20.00 each set 
 
 1/16th scale HD 3d printed US AFV Soft Skin antenna base mount pack set. Set includes 5 antenna base mounts that are depicted as mounted in the horizontal configuration...$20.00 each set 
 1/16th scale HD 3d printed US AFV Soft Skin antenna base mount pack vertical set. Set includes 5 antenna base mounts that are fitted in the vertical configuration...$20.00 each set 
 3D pritned German AFV tubular convoy light / round reflector set. Set comes in two options, filterless / sleeveless, and with the filter. Both convoylight options come with a round reflector...$26.00 each set 
 
 
 3D Printed Tiger I Manual starter cover cap...$10.50 each 
 3D Printed initial / early Tiger I rear Notek convoy light and reflector detail set. Set includes one early pattern Notek blackout light and one reflector...$12.00 each set 
 3D Printed initial tiger I rear mud flaps set. Set includes a right and left hand rear mud flap...$35.00 each set 
 3D Printed initial / early Tiger I pattern front double track rack set...$16.50 each set 
 3D Printed M4A3 static rear folding storage rack kit. Kit is printed in HD material and depicts the rack in it's open deployed state. This set is designed to be a quicker and less complex option compared to the full function piece...$61.00 each 
  3D Printed M4A3 functional rear folding storage rack kit. Kit is Printed in HD material and the kit is supplied with all the components required to build one fucntional rear folding storage rack...$55.00 each 
3D Printed German WWII AFV Antenna base... $10.00 each 
 3D Printed Chinese Type 59B 105mm gun conversion for the Hooben T55 kit. $25.00 Each 
 3D Printed Tiger I Turret visor set. Set includes 2 visors (enough for 1 tiger I turret). Set is designed to replace the undetailed molded in visors on the HL, and Mato tiger I models...$10.50 each set. 
 3D Printed Early Tiger I Bow MG Tarpaulin / snorkel cover cap wing nuts set. One set comes with 2 wing nuts (enough for 1 tiger tank)...$18.50 each set Bow MG, barrel and ball NOT included! 
 Resin HL / Taigen M26 mantlet rotor upgrade set. Set includes two drop in detail inserts to upgrade the stock Heng Long or Taigen rotor side panels...$9.50 each set span class="auto-style2">*To mount on the ECA set you need to diss assemble the turret, slide off the mantlet, and swap out the kit detail inserts with the ECA ones. 
 Resin HL / Tagen M26 Pershing family turret spare track assembly set. Set is designed to replace the basic spare track setup on the HL and Taigen M26 pershing models...$9.50 each 
 Resin 2nd pattern M26 main gun travel lock conversion set. Set includes enough components to replace the T26E3 pattern travel lock with the 2nd version which was used on the M26 Pershing...9.50 each set 
 Resin HL / Taigen M26 Pershing gunner's optic detail insert. Insert is designed to replace the exposed turret mounted airsoft firing LED that are mounted in the gunner's optic position on the Heng long and Taigen M26 pershing turret. Insert is desiged to be added in place of the LED. Insert is also hollow to allow the LED to be mounted to the insert for Airsoft firing light...6.50 each 
 Resin M26 / M26A1 Bow hull periscope plug conversion set. Set is designed to convert the bow hull area of the pershing from the T23E3, to a M26 / M26A1. With this set you remove the molded in backup periscope detailing on the front hull and drop in these two detail plugs in their place...6.00 each set 
 Resin M26 bottom rear hull access cap...$3.50 each set 
 Resin M26 Pershing top deck Fire Extinguisher box...$4.50 each *Note the HL and Taigen M26 models feature location for 2 Extinguishers, this is an error with both the HL and taigen model. The M26 only has ONE of these units and they are found on the right hand side of the tank, the location on the driver's side gets deleted. 
 HL / Taigen Resin M26 Pershing replacement bow headlight set. Set includes two headlights that are designed to replace the molded in versions found on both the Heng Long and Taigen M26 Pershing tank series. The set is designed to slip over the stock LED and replaces the plastic casing that is present on the base models...$5.50 each set 
 Resin HL / Taigen M26 Pershing barrel extension adapter. This component corrects the length od the HL / Tagien Pershing barrels to the correct length...$6.00 each 
Resin US AFV rear bustle 50.cal storage pintle, *note the Barrel clamps, and the barrel shroud clamp is not included.... 5.50 each 
 Resin M4 sherman Exhaust manifold set. Set includes enough parts to assemble one manifold. span class="auto-style2">*Note, the resin parts are not hollow and need to be hollowed by the builder in order to have the smoke system smoke flow throw the unit. ...$6.00 each set 
 Resin M4 sherman rear engine doors set... $5.50 each set 
 Resin Heng Long Tiger I turret Lift lugs detail set. Set contains 3 Turret lift lugs for upgrading a Heng Long Tiger I turret...$9.50 each set  Resin replacement Taigen Tiger I Rear Turret lift lug...$4.50 each 
 Resin Late Production Tiger I Hub cap insert set. Set Is designed to add the absent Hub cap detailing on the Taigen Late production tiger I model. Set is a drop in installation...$5.50 each set 
 Resin Late Production Tiger I rear Engine deck air intake set. Set is designed to replace the molded in early pattern air intake found on the Taigen Tiger I model...$6.00 each set 
 Resin Late Production Tiger I copula periscope inserts set. Set includes enough inserts for one Late copula...$5.50 each set 
 Resin Tiger I rear top deck tow cable securing locks set. Set includes enough parts for 1 tiger tank (4 locks, for 2 cables) Set is designed for use with plastic tow cables (Tamiya, Heng Long, Taigen)...$7.50 each set 
 Resin Late Tiger I Turret neck protective ring...$6.50 each 
 Resin Late Tiger I pistol port plug...$4.50 each  Resin Tiger I track pin aligner set. Set comes with two aligners..$3.50 each set 
Resin M1 Abrams replacement loader's hatch set. Set includes enough components for one loader's hatch. Set is designed to be a drop in replacement for the stock HL loader's hatch. Set is availabe in either opaque or clear resin Standard resin...$5.50 each Clear Resin... $7.00 each 
 Resin M1 Abrams secondary antenna base and mast set. Set includes one resin mast and one flex resin antenna base... $7.00 each set 
 Flex Resin M1 Abrams antenna base set. Set includes two flexible antenna bases. Set is desinged to replace the stock metal plugs that are present on the HL M1A2 abrams model...$10.00 each set 
 Resin M1 Abrams Spare wheel set. Set includes one spare wheel, and one track tooth in order to mount the wheel to the rear turret bin rail... $5.50 each set  Resin replacement US AFV Fluid filler armored cover caps set. Set includes 4 caps and length of wire for use for handles... $5.50 each set.  Resin M4A3 Bottom sponson detail set. Set includes a Little Joe aux. generator exhaust conduit, and two bottom sponson access caps... $5.50 Each Set 
 Resin VVSS sherman bogie bottom fastener set. Set incudes enough details for 1 VVSS sherman with spares... $6.50 each set 
 Resin 1/16th scale Sherman tank upper hull tow cable detail set. Set includes two tow cable Cleats, and two tow cable clamps. One set is enough for 1 sherman tank... $8.50 each  Resin 1/16th scale Heng Long Idler mount detail set. Set includes two replacement idler mounts for the Heng Long Sherman series. This set is a drop in replacement and are more accurate then the kit supplied parts...$6.50 each set 
  Resin 1/16th scale Heng Long M4A3 Sherman tank rear Hull extension upgrade set. Set is designed to add the missing rear hull portions to the rear lower hull section of the Heng Long M4A3 Sherman. Set includes enough parts to upgrade 1 Sherman...$8.50 each 
 1/16th scale RC remote recharge Jack cable. A drop in addition which allows you to recharge the 1/16th scale tank model from a hatch without having to take apart the tank's hull. The cable Is a drop in replacement and no soldering or electrical mods are needed, available for different vehicle types...$40.00 eachbr />  Resin 1/16th scale US AFV turret retracting pintle mount set...$5.50 each 
 Resin IDF pattern turret smoke grenade discharger set. Set includes 4 disschargers for use on IDF shermans...$9.50 each set 
 Resin IDF M50 Super Sherman rear turret counter weight conversion set. Set includes the counter weight, lift rings, metal wire, and the hatch lock. *Antenna bases NOT included...$20.00 each set 
 Resin Tiger I Initial production conversion set. Set includes Two side turret bins, vertical mounted tool box, and the rear antenna base mount...$45.00 each set *Built model uses Elite Armor decals, Highly recomended. 
 Resin Tiger I replacement Jack kit...$9.50 each 
 Resin Tiger I rear exhaust manifold set. Set includes two armored covers, two exhaust stacks, and two printed puffer caps. Solid resin manifolds...$18.00 each set Drilled out manifolds (for smoke)...$26.00 each set 
 Resin Tiger I front hull center Blower...$4.50 each 
 Resin Tiger I Headlight conduit and cover cap set. Set comes with two resin caps and two lengths of wire for the conduit. *Headlights Not included.... $5.50 each set 
Resin IDF M50 Sherman Early pattern main gun travel lock set. Set includes enough parts to assemble one travel lock...$12.00 each set 
  Resin IDF Sherman aux. generator side exhaust set. Set includes exhaust and heat shield...$6.50 each set 
 Resin IDF Sherman rear communication box set. Set includes enough components to assemble one box...$8.50 each 
 Resin IDF Sherman HVSS spare track rack set. Set includes enough componets to assemble two track racks...$12.00 each set 
 Resin IDF Sherman HVSS spare wheel mount set. Set includes two resin wheel mounts, and brass fasteners. Road wheels and rubber tires not included...$8.50 
 Resin IDF bow grab handle...$2.00 each 
 Resin IDF early M51 / M50 sherman rear engine hatch conversion set. Set includes IDF style early exhaust and IDF style elevated rear engine hatch...$8.50 each 
 Resin M4 sherman family rear tow hitch mount...$4.50 each  Resin M4 sherman family rear Tow shackles set. Set contains two thicker and two thinner shackles...$4.50 each set 
 Resin jerry can, in IDF holder set. Set is intended for early batch 1 (six Day War) era IDF M51 shermans. Set contains 7 jery cans... 10.00 each set 
 Resin IDF Searchlight set. Set contains enough components to assemble and mount one searchlight. Included are all fasteners, power cable, clear plastic, and a clear resin bulb. $13.00 each set 
 Resin Tamiya M51 Sherman Gunner's scope detail insert. Insert is designed to plug the inaccurate "hole" on the tamiya M51 turret with the correct gunner's scope detailing...$4.50 each 
 Resin M4 Sherman family fire extinguisher box...$4.50 each 
 Resin US AFV M1919 Bow MG ball cover...$4.50 each 
 Resin Post war NATO style light set. These lights are mounted on the front portion of the M50 / M51 sherman as a blackout light. On these tanks this light replaces the front siren. Set includes light, metal mounting strip, and wire...$5.00 each set 
 Resin IDF M51 Super Sherman Batch 1 replacement rear deck set. Set is designed to replace the inaccurate rear deck on the stock Tamiya M51 Kit, or to convert any other 1/16th scale sherman to an IDF M50 or M51. The engine deck is for the Batch 1 style M51. Kit contains enough parts to assemble one engine deck...$13.00 each set 
 Resin M26A1 early cut down M3A1 90mm Muzzle break and bore evacuator set. Set includes the Bore evacuator and the muzzle break...10.00 each set. 
 Resin M26A1 M3A1 90mm Muzzle break style 1, early cut down version. Muzzle break Only Bore Evacuator Not Included...$8.00 each. 
Resin M26A1 Pershing exhaust manifold set. Set includes the exhaust manifold, and the A1 style top deck retracting travle lock. This set is designed as a replacement for the stock Tamiya / HL M26 (T26E3) exhaust travel lock cluster. The new travle lock is designed to use the top hing portion and metal swing plates of the tamiya travle lock. Funconality is also retained in this set... $8.00 each set. 
 
 Resin M26 Pershing Final Drive support brackets set. Set includes 2 brackets...$5.50 each set  Resin 1/16th scale M4A3 Sherman tank exhaust manifold set. Set includes two M4A3 exhausts stacks...$6.00 each set. 
Resin 1/16th scale US AFV funnel horn set. Set includes horn, wire, and steel strip for mounting...$4.50 each set. 
 1/16th scale MP-48 Spring antenna base set. Set is offered in several options listed below 
 
 Kit Form...$6.00 each Fully assembled...$9.50 each  |
|
| Home1/6th scale1/35th scaleModel GalleryContactLinks | |
